国际口腔医学杂志 ›› 2020, Vol. 47 ›› Issue (4): 418-423.doi: 10.7518/gjkq.2020059

• 论著 • 上一篇    下一篇

遮色层厚度对聚醚醚酮-Crea.lign修复体颜色的影响

张婧婷1,潘旭东1,张文云2()   

  1. 1.昆明市中医医院口腔科 昆明 650500
    2.联勤保障部队第九二〇医院口腔科 昆明 650200
  • 收稿日期:2019-09-15 修回日期:2020-03-16 出版日期:2020-07-01 发布日期:2020-07-10
  • 通讯作者: 张文云
  • 作者简介:张婧婷,医师,硕士,Email:1329041031@qq.com

Effect of opaque-shade resin layer thickness on the color of polyetheretherketone-Crea.lign restoration

Zhang Jingting1,Pan Xudong1,Zhang Wenyun2()   

  1. 1. Dept. of Stomatology, Kunming Municipal Hospital of Traditional Chinese Medicine, Kunming 650500, China
    2. Dept. of Stomatology, 920th Hospital of Joint Logistics Support Force, Kunming 650200, China
  • Received:2019-09-15 Revised:2020-03-16 Online:2020-07-01 Published:2020-07-10
  • Contact: Wenyun Zhang

摘要:

目的 研究不同遮色层厚度对牙本质色聚醚醚酮(PEEK)-Crea.lign修复体颜色的影响。方法 制备厚度0.6 mm PEEK试件,在其表面粘接厚度分别为0.0、0.1、0.2、0.3、0.4、0.5 mm的遮色层,体层厚度皆为1.0 mm的A2色系Crea.lign树脂修复系统,测量各组试件的L*a*b*值,并计算各组之间的色差值。结果 0.0 mm体层+ 0.1~0.3 mm遮色层以及1.0 mm体层+0.0~0.2 mm遮色层,随遮色层厚度的增加,L*a*b*值均呈上升趋势。体层厚度为0.0 mm和(或)1.0 mm,0.1~0.5 mm遮色层厚度组间色差在临床可接受范围内,与牙本质色PEEK之间的色差超过临床可接受范围。结论 在临床适用范围内,0.1~0.5 mm的遮色层厚度变化不会对牙本质色PEEK-Crea.lign修复体的颜色产生明显影响,0.1 mm为可以遮住牙本质色PEEK底色的最小遮色层厚度。

关键词: 聚醚醚酮, Crea.lign树脂, 厚度, 颜色

Abstract:

Objective This study aimed to test the effect of different thicknesses of opaque-shade resin layer on the color of detin-shade polyetheretherketone (PEEK)-Crea.lign restoration. Methods PEEK of 0.6 mm thickness was synthesized, and A2 shade Crea.lign of opaque-shade resin layers of 0.0, 0.1, 0.2, 0.3, 0.4, and 0.5 mm and body-shade resin layer of 1.0 mm were bonded on the surface of PEEK. CIE (International Commission on illumination) L*a*b* values for specimens were measured, and color difference among the different thickness groups was calculated. Results For the 0.0 mm body-shade resin layer + 0.1-0.3 mm opaque-shade resin layer and 1.0 mm body-shade resin layer + 0.0-0.2 mm opaque-shade resin layer, the color values showed an upward trend with the increasing thickness of the opaque-shade resin layer. When the thicknesses of PEEK and body-shade resin layer were constant at 0.0 and/or 1.0 mm respectively, the color differences between each group of 0.1-0.5 mm-thick opaque-shade resin layer were within the clinical acceptable range. Beyond clinically acceptable color difference was observed for the detin-shade PEEK. Conclusion In clinical setting, the 0.1-0.5 mm thickness range of opaque-shade resin layers did not influence the color of the detin-shade PEEK-Crea.lign restoration. In addition, 0.1 mm was the minimum thickness that sufficiently covered the detin-shade PEEK background.

Key words: polyetheretherketone, Crea.lign resin, thickness, color

中图分类号: 

  • R783.1

图 1

圆孔状不锈钢模具"

图 2

自制暗盒"

图 3

试件固定于暗盒上"

表 1

不同遮色层厚度的色度值(无体层树脂)"

分组 L* a* b*
PEEK 81.900±0.322a 0.533±0.082c 22.658±0.134a
O-1 80.909±0.598ab 1.283±0.167b 21.167±0.281b
O-2 81.642±0.279a 1.475±0.206ab 21.300±0.363b
O-3 81.809±0.518a 1.525±0.096ab 21.483±0.111b
O-4 81.642±0.478a 1.658±0.069a 21.550±0.301b
O-5 80.517±0.477b 1.792±0.181a 22.133±0.127b

表 2

不同遮色层厚度+1.0 mm体层的色度值"

分组 L* a* b*
无遮色层 71.573±0.228c 3.100±0.197c 23.920±0.403b
OB-1 73.473±0.205ab 4.187±0.228b 26.153±0.051a
OB-2 73.740±0.125a 4.226±0.072ab 26.540±0.123a
OB-3 73.542±0.126ab 4.258±0.100ab 26.592±0.261a
OB-4 73.407±0.064b 4.367±0.078ab 26.567±0.227a
OB-5 73.373±0.128b 4.493±0.104a 26.313±0.186a

表 3

各遮色层厚度组间的色差值(无体层树脂)"

分组 PEEK O-1 O-2 O-3 O-4
O-1 2.002±0.366 - - - -
O-2 1.776±0.183 1.130±0.371 - - -
O-3 1.596±0.185 1.188±0.774 0.535±0.231 - -
O-4 1.715±0.366 0.992±0.632 0.712±0.229 0.776±0.278 -
O-5 2.294±0.442 0.870±0.398 1.266±0.572 1.349±0.927 1.274±0.642

表 4

各遮色层厚度组间的色差值(体层厚度1.0 mm)"

分组 无遮色层 OB-1 OB-2 OB-3 OB-4 OB-5
OB-1 3.135±0.560 - - - - -
OB-2 3.588±0.508 0.558±0.058 - - - -
OB-3 3.502±0.636 0.510±0.302 0.313±0.094 - - -
OB-4 3.466±0.543 0.534±0.296 0.435±0.149 0.419±0.107 - -
OB-5 3.314±0.614 0.464±0.227 0.540±0.128 0.471±0.196 0.400±0.139 -
PEEK 10.731±0.457 9.837±0.412 9.737±0.291 9.968±0.344 10.154±0.236 10.052±0.261
[1] Apeldorn T, Keilholz C, Wolff-Fabris F, et al. Die-lectric properties of highly filled thermoplastics for printed circuit boards[J]. J Appl Polym Sci, 2013,128(6):3758-3770.
[2] Hahnel S, Wieser A, Lang R, et al. Biofilm formation on the surface of modern implant abutment materials[J]. Clin Oral Implants Res, 2015,26(11):1297-1301.
doi: 10.1111/clr.12454 pmid: 25060652
[3] Pradeep N, Sreekumar AV. An in vitro investigation into the cytotoxicity of methyl methacrylate monomer[J]. J Contemp Dent Pract, 2012,13(6):838-841.
doi: 10.5005/jp-journals-10024-1239 pmid: 23404013
[4] Rothmund L, Shehata M, van Landuyt KL, et al. Release and protein binding of components from resin based composites in native saliva and other extraction media[J]. Dent Mater, 2015,31(5):496-504.
doi: 10.1016/j.dental.2015.01.016 pmid: 25724383
[5] Rekow ED, Bayne SC, Carvalho RM, et al. What constitutes an ideal dental restorative material[J]. Adv Dent Res, 2013,25(1):18-23.
doi: 10.1177/0022034513502206 pmid: 24129813
[6] Maldonado-Naranjo AL, Healy AT, Kalfas IH. Po-lyetheretherketone (PEEK) intervertebral cage as a cause of chronic systemic allergy: a case report[J]. Spine J, 2015,15(7):e1-e3.
doi: 10.1016/j.spinee.2015.04.011 pmid: 25862511
[7] Stawarczyk B, Beuer F, Wimmer T, et al. Polyethere-therketone—a suitable material for fixed dental pros-theses[J]. J Biomed Mater Res Part B Appl Biomater, 2013,101(7):1209-1216.
doi: 10.1002/jbm.b.32932 pmid: 23564476
[8] Najeeb S, Zafar MS, Khurshid Z, et al. Applications of polyetheretherketone (PEEK) in oral implantology and prosthodontics[J]. J Prosthodont Res, 2016,60(1):12-19.
doi: 10.1016/j.jpor.2015.10.001 pmid: 26520679
[9] 姚江武, 高承志. 现代口腔色彩学[M]. 厦门: 厦门大学出版社, 2000: 27-28.
Yao JW, Gao CZ. Modern dental color science[M]. Xiamen: Xiamen University Press, 2000: 27-28.
[10] 陶娴, 姚江武. 色差公式及其在口腔医学中的应用[J]. 口腔医学研究, 2013,29(4):378-380.
Tao X, Yao JW. Color difference formula and its application in stomatology[J]. J Oral Sci Res, 2013,29(4):378-380.
[11] 夏春明. 光固化复合树脂颜色相关性能研究[D]. 西安: 第四军医大学, 2002.
Xia CM. Study of color-related properties of light-curing composite resins[D]. Xi’an: The Fourth Military Medical University, 2002.
[12] 肖丹, 姚远, 黄丰, 等. 不同桩核对Lava锆瓷冠颜色影响的实验研究[J]. 口腔医学研究, 2017,33(7):774-776.
Xiao D, Yao Y, Huang F, et al. Influence of four kinds of post-cores on color of lava all ceramic system[J]. J Oral Sci Res, 2017,33(7):774-776.
[13] Taufall S, Eichberger M, Schmidlin PR, et al. Fracture load and failure types of different veneered polye-theretherketone fixed dental prostheses[J]. Clin Oral Investig, 2016,20(9):2493-2500.
doi: 10.1007/s00784-016-1777-4 pmid: 26979441
[14] Stawarczyk B, Thrun H, Eichberger M, et al. Effect of different surface pretreatments and adhesives on the load-bearing capacity of veneered 3-unit PEEK FDPs[J]. J Prosthet Dent, 2015,114(5):666-673.
doi: 10.1016/j.prosdent.2015.06.006 pmid: 26344191
[15] 贾爽, 陈栋, 王德芳. EverStick高强纤维树脂贴面用于四环素牙美容修复的临床评价[J]. 口腔材料器械杂志, 2017,26(2):96-101.
Jia S, Chen D, Wang DF. Clinical assessment of using EverStick fiber-reinforced composite veneer to restore tetracycline pigmentation teeth[J]. Chin J Dent Mater Devices, 2017,26(2):96-101.
[16] 郭航, 王峰, 冯化端, 等. 4 340例烤瓷修复体选色调查[J]. 华西口腔医学杂志, 2000,18(3):174-177.
Guo H, Wang F, Feng HD, et al. The investigation of color selection of 4 340 cases of ceramic restorations[J]. West China J Stomatol, 2000,18(3):174-177.
[17] 孙剑, 王忠义, 余建军. Vita比色板色度学分析及临床应用的合理性[J]. 实用口腔医学杂志, 1998,14(3):175-176.
Sun J, Wang ZY, Yu JJ. Color analysis and reasona-bleness in applying of Vita shade guide[J]. J Pract Stomatol, 1998,14(3):175-176.
[18] 王培, 高平. 遮色剂对Ceramage色彩的影响[J]. 天津医药, 2008,36(6):457-458.
Wang P, Gao P. Effect of opaque resin on color of Ceramage[J]. Tianjin Med J, 2008,36(6):457-458.
[19] Paul SJ, Peter A, Rodoni L, et al. Conventional visual vs spectrophotometric shade taking for porcelain-fused-to-metal crowns: a clinical comparison[J]. Int J Periodontics Restorative Dent, 2004,24(3):222-231.
pmid: 15227770
[20] Joiner A. Tooth colour: a review of the literature[J]. J Dent, 2004,32(Suppl 1):3-12.
[21] 袁坤, 王辉, 张凌, 等. 三种电脑比色仪比色准确性与可靠性的比较[J]. 临床口腔医学杂志, 2010,26(3):177-180.
Yuan K, Wang H, Zhang L, et al. Comparison of accuracy and reliability of three computer-aid shade matching instruments[J]. J Clin Stomatol, 2010,26(3):177-180.
[22] Kamishima N, Ikeda T, Sano H. Color and translu-cency of resin composites for layering techniques[J]. Dent Mater J, 2005,24(3):428-432.
doi: 10.4012/dmj.24.428 pmid: 16279735
[23] Nazari V, Ghodsi S, Alikhasi M, et al. Fracture stren-gth of three-unit implant supported fixed partial den-tures with excessive crown height fabricated from different materials[J]. J Dent (Tehran), 2016,13(6):400-406.
[24] Schwitalla AD, Spintig T, Kallage I, et al. Pressure behavior of different PEEK materials for dental im-plants[J]. J Mech Behav Biomed Mater, 2016,54:295-304.
doi: 10.1016/j.jmbbm.2015.10.003 pmid: 26492595
[1] 黄依欢,李委航,马典,陈瑾,钱捷,李旭东. IPS e.maxCAD和Lava Ultimate在贴面修复中的有限元分析[J]. 国际口腔医学杂志, 2023, 50(4): 423-432.
[2] 王蕾,叶玲,汪成林. 牙齿内漂白并发症的处理及预防策略[J]. 国际口腔医学杂志, 2023, 50(3): 359-365.
[3] 曾芳,王剑. 全锆冠美学修复效果的影响因素[J]. 国际口腔医学杂志, 2022, 49(2): 233-238.
[4] 沈冬妮,施莹,傅柏平. 后牙牙合贴面修复的研究进展[J]. 国际口腔医学杂志, 2021, 48(3): 287-291.
[5] 钱慧芬,林云红,吴美莹,代自超,李星星. 瓷层厚度和变色基底对瓷贴面修复四环素牙光学性能的影响[J]. 国际口腔医学杂志, 2020, 47(4): 413-417.
[6] 鲁雨晴,闵婕,陈昕,刘春煦,董博,岳莉,于海洋. 整体切削的聚醚醚酮可摘局部义齿即刻修复1例[J]. 国际口腔医学杂志, 2020, 47(3): 297-303.
[7] 陈昕,毛渤淳,鲁雨晴,董博,朱卓立,岳莉,于海洋. 钴铬合金和聚醚醚酮用于可摘局部义齿支架的三维有限元分析[J]. 国际口腔医学杂志, 2019, 46(5): 526-531.
[8] 于婉琦,周延民,赵静辉. 口腔种植体新材料的研究现状[J]. 国际口腔医学杂志, 2019, 46(4): 488-496.
[9] 黄满英,付云. 牙龈生物型的测量方法[J]. 国际口腔医学杂志, 2019, 46(2): 171-176.
[10] 刘玲玲,刘树泰. 上颌腭侧软组织厚度的测量方法及影响因素[J]. 国际口腔医学杂志, 2019, 46(2): 234-237.
[11] 张停停,宗娟娟. 自体结缔组织移植术的研究现状[J]. 国际口腔医学杂志, 2019, 46(1): 89-93.
[12] 靳志亨,李清. 核瓷和饰瓷厚度变化对全瓷修复体抗弯强度影响的研究进展[J]. 国际口腔医学杂志, 2019, 46(1): 94-98.
[13] 秦胜男,贾慧,李英. 聚醚醚酮在口腔临床中的应用现状[J]. 国际口腔医学杂志, 2018, 45(6): 652-656.
[14] 陈曦,于海洋. 聚醚醚酮在口腔种植与修复领域的研究进展[J]. 国际口腔医学杂志, 2018, 45(6): 657-665.
[15] 罗志强, 叶钟泰. 新疆地区不同人群上颌窦外侧骨壁厚度的锥形束CT测量分析[J]. 国际口腔医学杂志, 2017, 44(1): 55-58.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 张新春. 桩冠修复与无髓牙的保护[J]. 国际口腔医学杂志, 1999, 26(06): .
[2] 王昆润. 长期单侧鼻呼吸对头颅发育有不利影响[J]. 国际口腔医学杂志, 1999, 26(05): .
[3] 彭国光. 颈淋巴清扫术中颈交感神经干的解剖变异[J]. 国际口腔医学杂志, 1999, 26(05): .
[4] 杨凯. 淋巴化疗的药物运载系统及其应用现状[J]. 国际口腔医学杂志, 1999, 26(05): .
[5] 康非吾. 种植义齿下部结构生物力学研究进展[J]. 国际口腔医学杂志, 1999, 26(05): .
[6] 柴枫. 可摘局部义齿用Co-Cr合金的激光焊接[J]. 国际口腔医学杂志, 1999, 26(04): .
[7] 孟姝,吴亚菲,杨禾. 伴放线放线杆菌产生的细胞致死膨胀毒素及其与牙周病的关系[J]. 国际口腔医学杂志, 2005, 32(06): 458 -460 .
[8] 费晓露,丁一,徐屹. 牙周可疑致病菌对口腔黏膜上皮的粘附和侵入[J]. 国际口腔医学杂志, 2005, 32(06): 452 -454 .
[9] 赵兴福,黄晓晶. 变形链球菌蛋白组学研究进展[J]. 国际口腔医学杂志, 2008, 35(S1): .
[10] 庞莉苹,姚江武. 抛光和上釉对陶瓷表面粗糙度、挠曲强度及磨损性能的影响[J]. 国际口腔医学杂志, 2008, 35(S1): .