国际口腔医学杂志 ›› 2017, Vol. 44 ›› Issue (3): 301-303.doi: 10.7518/gjkq.2017.03.010

• 论著 • 上一篇    下一篇

不同切端设计的上前牙瓷贴面受载能力的定量研究

张雅蓉1, 刘洋2, 张玲1, 于海洋1   

  1. 1.口腔疾病研究国家重点实验室,国家口腔疾病临床研究中心,四川大学华西口腔医院修复科 成都 610041;
    2.口腔疾病研究国家重点实验室,国家口腔疾病临床研究中心,四川大学华西口腔医院关节科 成都 610041
  • 收稿日期:2016-12-15 修回日期:2017-02-17 出版日期:2017-05-01 发布日期:2017-05-01
  • 通讯作者: 于海洋,教授,博士,Email:yhyang6812@scu.edu.cn
  • 作者简介:张雅蓉,硕士,Email:674097928@qq.com
  • 基金资助:
    国家自然科学基金(81300859)

Quantitative analysis of the load tolerance of maxillary incisors with ceramic-laminated veneers for various incisal margin preparations

Zhang Yarong1, Liu Yang2, Zhang Ling1, Yu Haiyang1   

  1. 1. State Key Laboratory of Oral Diseases, National Clinical Research Center for Oral Diseases, Dept. of Prosthodontics, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, China;
    2. State Key Laboratory of Oral Diseases, National Clinical Research Center for Oral Diseases, Dept. of Temporomandibular Joint, West China Hospital of Stomatology, Sichuan University, Chengdu 610041, China
  • Received:2016-12-15 Revised:2017-02-17 Online:2017-05-01 Published:2017-05-01
  • Supported by:
    This study was supported by National Natural Science Foundation of China(81300859).

摘要: 目的 瓷贴面因美观、微创的特点在临床上广为应用,但其使用寿命和破坏载荷的相关数据目前尚不清楚。该研究通过体外实验测定不同材料、不同设计的上前牙瓷贴面可承受的最大应力载荷,为前牙瓷贴面修复提供基础数据。方法 160颗离体上中切牙,随机分为8组,分别按照对接、切端包绕设计行牙体预备,用铸造玻璃陶瓷和氧化锆陶瓷制作贴面,并粘接;在万能测试机上进行不同受力方向的最大载荷实验,考察修复体对载荷的承受能力。结果以60°和125°方向加载时,铸造玻璃陶瓷贴面的对接设计对载荷的承受能力均高于切端包绕设计,而切端包绕设计更利于氧化锆瓷贴面对载荷应力的分布。在以60°方向加载时,对于切断包绕设计,氧化锆陶瓷对载荷的承受能力明显优于铸造玻璃陶瓷,但对于对接设计,二者间并无明显差异。以125°方向加载时,在同种设计中,无论是切端包绕设计或对接设计,氧化锆陶瓷可承受的最大应力载荷均高于铸造玻璃陶瓷。结论 切端包绕设计的应力抵抗优于切端对接设计;氧化锆贴面目前存在粘接困难,但其破坏强度明显优于铸造玻璃陶瓷,有较好的潜在应用价值。

关键词: 瓷贴面, 铸造玻璃陶瓷, 氧化锆陶瓷, 切端包绕设计, 切端对接设计

Abstract: Objective Ceramic-laminated veneer has been extensively used in clinics due to its aesthetics and minimally invasive performance. However, its working life and load tolerance remain unclear. This in vitro study aimed to investigate the stress tolerance of different ceramic-laminated veneer designs and materials for incisor restorations. Methods A total of 160 extracted human maxillary incisors were randomly divided into eight groups. Each group was assigned with tooth preparations of the palatal chamfer design or butt joint design, and the materials used were castable glass ceramic or zirconia ceramic. The veneers were bonded to the teeth and subsequently subjected to a maximum loading test on a universal testing machine in different loading angles to check the load tolerance. Results The load tolerance of the butt joint design with castable glass ceramic-laminated veneers was better than that of the palatal chamfer design at both loading angles of 60°and 125°. However, the palatal chamfer design with zirconia ceramic had better concentrated stress distribution. With the 60° loading angle, the palatal chamfer design with zirconia ceramic tolerated the load better than that with the castable glass ceramic. However, they were not significantly different from the butt joint design. At the loading angle of 125°, the zirconia ceramic-laminated veneers showed significantly better load tolerance for both the palatal chamfer design and the butt joint design. Conclusion The palatal chamfer design showed significantly better load tolerance than the butt joint design. Although bonding difficulties were observed in the zirconia ceramic-laminated veneer, the material still had potential clinical application value due to the favorable stress tolerance.

Key words: ceramic-laminated veneer, castable glass ceramic, zirconia ceramic-laminated veneer, palatal chamfer design, butt joint design

中图分类号: 

  • R783.3
[1] Castelnuovo J, Tjan AH, Phillips K, et al. Fracture load and mode of failure of ceramic veneers with different preparations[J]. J Prosthet Dent, 2000, 83 (2):171-180.
[2] Zarone F, Apicella D, Sorrentino R, et al. Influence of tooth preparation design on the stress distribution in maxillary central incisors restored by means of alumina porcelain veneers: a 3D-finite element an-alysis[J]. Dent Mater, 2005, 21(12):1178-1188.
[3] Stappert CF, Ozden U, Gerds T, et al. Longevity and failure load of ceramic veneers with different pre-paration designs after exposure to masticatory sim-ulation[J]. J Prosthet Dent, 2005, 94(2):132-139.
[4] Meijering AC, Creugers NH, Roeters FJ, et al. Sur-vival of three types of veneer restorations in a clinical trial: a 2.5-year interim evaluation[J]. J Dent, 1998, 26(7):563-568.
[1] 黎敏,华成舸,蒋丽. 提高氧化锆陶瓷粘接性能新技术的研究进展[J]. 国际口腔医学杂志, 2021, 48(4): 485-490.
[2] 钱慧芬,林云红,吴美莹,代自超,李星星. 瓷层厚度和变色基底对瓷贴面修复四环素牙光学性能的影响[J]. 国际口腔医学杂志, 2020, 47(4): 413-417.
[3] 魏煦, 杨芸, 张凯, 孙方方. 热压铸瓷面瓷贴面的临床效果评估[J]. 国际口腔医学杂志, 2017, 44(6): 696-700.
[4] 姚陈敏, 周丽群, 黄翠. 前牙磨耗牙色修复材料的选择[J]. 国际口腔医学杂志, 2017, 44(3): 363-367.
[5] 陈丽娟1 孟庆飞2 万延俊1. 不同设计类型的IPS Empress铸瓷贴面前牙美学修复的疗效观察[J]. 国际口腔医学杂志, 2016, 43(5): 511-514.
[6] 陆轩,陈小冬,邢文忠,李振春. 全瓷贴面修复的临床效果评估[J]. 国际口腔医学杂志, 2015, 42(2): 170-172.
[7] 景页 孟翔峰. 自粘接树脂水门汀与二氧化锆陶瓷间粘接耐久性的研究[J]. 国际口腔医学杂志, 2013, 40(3): 301-304.
[8] 林艺华1 宋晓萌2 张玮3. 3种树脂加强型玻璃离子与氧化锆陶瓷粘接性能的研究[J]. 国际口腔医学杂志, 2013, 40(3): 305-308.
[9] 刘天爽1 樊成2 李振春3 陈小冬3. 不同切端全瓷贴面的破坏力学分析[J]. 国际口腔医学杂志, 2012, 39(5): 565-567.
[10] 李中杰 浩志超综述 孟玉坤审校. 瓷贴面修复牙体不同预备类型比较的研究进展[J]. 国际口腔医学杂志, 2012, 39(4): 543-546.
[11] 刘晶莹综述 刘晓明审校. 不同牙体预备对瓷贴面力学性能和临床修复效果的影响[J]. 国际口腔医学杂志, 2012, 39(3): 404-407.
[12] 刘峰. 全瓷修复材料和方法的分化[J]. 国际口腔医学杂志, 2011, 38(4): 373-377.
[13] 孙学武 郝鹏杰 肖丽静. 即刻牙本质封闭对瓷贴面预备后基牙敏感程度的影响[J]. 国际口腔医学杂志, 2011, 38(3): 265-267.
[14] 钱海馨 张修银 杨丹苓. IPS-EMPRESS Ⅱ全瓷修复变色牙的临床效果[J]. 国际口腔医学杂志, 2011, 38(3): 274-276.
[15] 卫文娟综述 孙迎春,高平审校 . 瓷贴面修复临床应用的研究进展[J]. 国际口腔医学杂志, 2010, 37(5): 604-607.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 张新春. 桩冠修复与无髓牙的保护[J]. 国际口腔医学杂志, 1999, 26(06): .
[2] 王昆润. 长期单侧鼻呼吸对头颅发育有不利影响[J]. 国际口腔医学杂志, 1999, 26(05): .
[3] 彭国光. 颈淋巴清扫术中颈交感神经干的解剖变异[J]. 国际口腔医学杂志, 1999, 26(05): .
[4] 杨凯. 淋巴化疗的药物运载系统及其应用现状[J]. 国际口腔医学杂志, 1999, 26(05): .
[5] 康非吾. 种植义齿下部结构生物力学研究进展[J]. 国际口腔医学杂志, 1999, 26(05): .
[6] 柴枫. 可摘局部义齿用Co-Cr合金的激光焊接[J]. 国际口腔医学杂志, 1999, 26(04): .
[7] 孟姝,吴亚菲,杨禾. 伴放线放线杆菌产生的细胞致死膨胀毒素及其与牙周病的关系[J]. 国际口腔医学杂志, 2005, 32(06): 458 -460 .
[8] 费晓露,丁一,徐屹. 牙周可疑致病菌对口腔黏膜上皮的粘附和侵入[J]. 国际口腔医学杂志, 2005, 32(06): 452 -454 .
[9] 赵兴福,黄晓晶. 变形链球菌蛋白组学研究进展[J]. 国际口腔医学杂志, 2008, 35(S1): .
[10] 庞莉苹,姚江武. 抛光和上釉对陶瓷表面粗糙度、挠曲强度及磨损性能的影响[J]. 国际口腔医学杂志, 2008, 35(S1): .